Tag Archives: Luxury Coach Motorhome

It’s bedroom time

21/07/2017 Bernie Cross

Time to start fitting out the bedroom

Starting from the back of the coach to the front is the only way to go. Under the bed area is where the motor is, so the floor has a raised part, this is a great place to put in bedroom cupboards. With nothing being square or plum apart from the floor I was making it up as I went along. It’s nothing like building a house!

Lots of flat pack cupboard boxes to make up from Bunnings.

The bed should fit between the two bedside draws.

One bit at a time, this cover goes on so more draws can go on top.

Time to put some support in place and insulation before I go too far.

One more box and this level will be done.

With the black timber in place it only just fitted after shaving the back edges off the side boxes.

They only just made it in after Shaving off some timber.

No turning back now time to screw it in place.

Time for some sparky stuff

At this stage it was time to run some 12 volt cables for the LED lights as well as some USB chargers on either side of the bed. We need some speaker cables put in as well for the stereo that was going to go in later on. We are not running 240 volt in the bedroom as there is nothing we can think of that we need it for down this section of the bus so 240 volt is it .

All the power cables for the lights, USB charges and the stereo speakers are in. Lets hope that is all of it.

Time to fit in the down light before I go to far.

12v cables are in place as well as the insulation.

You can turn the LED lights any colour you like.

Now the led light strip in place and all powered up.

I have some fiddle bits of trim around the cupboards, which will be done later on when we get some other work out of the way first. All we have to do now is fit the draw runners on before putting the draws.

We have not decided what we actually want the walls to look like, there has been some ideas floating around but nothing that really makes us confident to want to finish them now. So I will be tidying up the bedroom walls with more ply where all the power cables run and then painting them till we find what kind for finish we are looking for.

Still Removing The Old Coach Air Conditioning

09/07/2017 Bernie Cross

Back To The Air-Conditioning

We had already done the first part of the work on the bedroom ceiling, but to finish that job. We had to rip the rest of the old air-con off the roof. I started with getting the sola panels off first, then remove the cover plates.

Now time to remove the solar panels again.

This will be the last time the roof looks like a coach roof

This will be the last time it will look like this.

The finished look of this project we will have a roof top deck up here, but not now that is a job for an other day. Now it’s time to remove the evaporator, heat exchange radiators and blowers. Stripping out the copper pipe, heat exchange radiator pipes as well all the electrical pits.

Stripping all the sparky stuff and back grill to accessing the pipe work.

Old air condition control unit in the ceiling.

One side of the evaporator, heat radiators and blowers to be removed.

More Stuff For The Scrap Yard

I did a trip to the scrap metal yard with all the copper, brass, evaporator and the heat exchange radiators. It’s always good to get some money back, that lot gave me $145 to put back into the project. Next will be cutting out all the aluminium that we don’t need off the roof air-condition area. I all ready have some that we have removed so that we will have an other trip to the scrap yard soon.

Did I see rain?

Well it did start raining on and off for a week, lucky we could put the covers over the holes and with some buckets inside it didn’t get too wet inside. This means I went back inside to do some more work on the bedroom/bathroom ceiling, while it rained but thats an other blog.

1st blog on THE OLD COACH AIR CONDITIONING

Motorhome fit out

Bedroom Ceiling…. Time To Prep

27/06/2017 Bernie Cross 4 Comments

Over My Head….. Just.

The bedroom ceiling is the lowest overall in the back of the coach, so it just touches the top of my head. The old ceiling carpet had already been removed by Des, so all I had to do was grind the toilet ceiling panel off then scrap back the foam underlay that was glued to the ceiling.

Old Toilet ceiling, it had a 10mm step down made out of sheetmetal.

Toilet ceiling after removing the sheetmetal panel.

Time To Remove The Underlay

With scraper in hand it was time to start scraping back all the old underlay. This might sound like an easy job, but it had been glued up there very well. I thought it wouldn’t take to long, but I was wrong again as the bedroom ceiling end up taking around 8hrs just to get the foam off.

Last of the foam off the bedroom ceiling.

Now To Get Rid Of That Glue

With the contacted glue still all over the ceiling, the only way that I could think to do was to put a sanding disc on a grinder and go for it. Well… it worked, I had been covered in glue and dust. Thank goodness for a dust mask and safety glasses as once I was finished the job there was crap all over the place.

All the old glue has gone with most of it on me…

I’ll Just Keep On Going

Now that I’ve started on the ceiling, I’ll keep on going and finish it all off inside the coach. The next project will be the bathroom then onto the kitchen ceiling area, so once I have cleaned all that up it will be ready to glue and pop rivet some white Colorbond sheet metal that came with the coach from Des. The ceiling is a good job to do when the weather is wet and raining so while its nice and fine I will go finish removing the old air-con on the roof above the bedroom, they are the wholes in the ceiling you can see on the photo.

Motorhome fit out

Locks For The Storage Bins

20/06/2017 Bernie Cross 2 Comments

Time to lock up the bins

With so much stuff we need to fit out the coach, as well as tools, it was time to fix the bin doors on the coach as well as the diesel tank. I don’t need to lose 1000 Lt of diesel, so I got to work. When we were at the Sarina Ranges house sit home of Larry and Elaine.

Are they in the right place?

After marking out where I thought the locks should go, then realised it won’t so it was time to mark them out again. I’m glad I didn’t drill the hole before double checking my work. Remember the rule measure twice cut once…., as it would not have been the first time I’ve stuff up.

Pilot whole to get started. (See punch mark in the wrong place below hole)

I used a whole saw to get the right size.

An a big hammer made the latch bar the right shape.

Barrel key alike so that the 1 key fit’s all locks.

Lock fitted in place just need to clean up.

One less job to do

So many small jobs to do when building a motorhome, you finish one and there are so many more to work on. At least all the bins are now locked up (six of them) and two diesel fill points on either side of the coach. If you ever start working on a project nothing ever go’s to plan, modification has become my middle name.

Motorhome fit out

Bedroom Walls & Windows

12/06/2017 Bernie Cross 2 Comments

Time For Some Inside Work

Now with the roof fixed while in Bowen, it was time to start on the bedroom. The first thing was the windows…. I had to remove the old toilet window which Des had put in, because for us it was in the wrong place.

Time to remove the old window so we can fit the new one’s

Des had kept the old panel he cut out for the window he put in.

Time For Some Walls

With the window in place it was back inside to fit the insulation and wall paneling 16mm ply the we got when living in Yulara N.T. First thing was to remove the old aluminium sheetmetal so we could put in the new insulation.

Removing old sheet metal to put the new insulation in.

With the inside panels going on its starting to look more like a bedroom, later we will be putting some kind of lament over the ply to finish it off.

Right side insulation and paneling going on.

Charmaine doing some OH & S, Insulation in and starting on the timber paneling after fitting the bedroom window on the left side.

Bedroom ready for the trip down the Queensland coast from Bowen.

So with the bedroom side walls in place it was time to set up the new sleeping area for the next part of our trip down the Queensland coast. We also had to re pack all the stuff we moved into the shed while house sitting in Bowen.

One step closer to having a motorhome, so the dream’s getting their slowly but we are on our way.

Motorhome fit out, On the road problems

Big Bus Big Adventure Air Conditioner ???

06/06/2017 Bernie Cross 2 Comments

Is The Air Conditioner Working

The condenser unit was fitted in the front bin on the drivers side and only had an out vent so if the bin door was closed, things didn’t work that well. This should have been one of the first things that I should have fixed, but as we were not on the road much I didn’t think about it at all. Now after driving from S.A. to N.T. and now into QLD, it was defiantly time to fix it.

Time For Some Modifications

To start with we had to seal the air-con unit to the outside bin door, so off to the hardware store for some sheetmetal. Ended up getting some flashing which would mean I would not have to bend any 90 angles. So out with the tin snips and pop rivet gun to make some ducting.

Made up some ducting to get the air out.

Rubber seals in place so the hot air only go’s outside.

Time For Some Intake Vents

Now all we had to do was the intake vents, I thought three would do for a start and thats all they had at the hardware. So back to the coach I went to start fitting the intake vents. First off was to mark out the holes for the vents then cut them out.

Marked and cut out ready for the new vents

New vents in place so no more over heating while driving down the road.

One Cool Motorhome.

Now that job is done It’s so much cooler inside when driving down the road. Also when we stay somewhere I don’t have to open up the air-con’s bin door again, now that all the hot air is blown outside.

Motorhome fit out, On the road problems

Time To Fix The Motorhome Roof

02/06/2017 Bernie Cross 2 Comments

Why Is It Wet In Here?

The only time it’s good to have a leaky roof is when their is nothing to get damaged inside. After a year thinking the roof was ok in Leigh Creek, we started having problems with the roof again. Mainly because where we moved to rained a bit more. To start off we thought it was only the fiberglass panels that were replaced from the old original bus windows that Des had fitted.

Thanks to Zac for his great help in getting the huge job started by cutting out the old Sikaflex. I was working six days a week @ Curtin Springs Station N.T., all I could manage was regluing after work. It did stop the water coming in around the fiberglass panels.

Fiberglass panels before we reglued then back in place.

Its Still Wet In Here.

Our first house sitting job was in Bowen for Michael and Michelle. We had no rain forecast for the next few days so Charmaine and myself started on the roof to fix the rest of the leaks. The first job was to remove the solar panels and hatches from the roof.

Removed the Solar panels now the hatches.

The Fun Starts Now …….Not !!!

The fun of sanding back the old paint job as well as getting rid of the surface rust around the hatches. It was one of those jobs you love to hate, but had to be done, so with buckets of water and sanding paper in hand it was head down & ass up and off to work we go.

I Do Like Painting

Time to undercoat….. we had been so lucky as it had been raining all the way around us and only that a couple of rain drops on the coach. So after I Sikaflexed all the joints it was time to undercoat using some Infrared Heat Reflective Primer.

Second undercoat, ended up with three coats

Now for the topcoat, the best part of the job as it’s almost done. Des (the bloke we got the coach before us), had already paid for the paint, so now it was time for three topcoats.

Topcoat Solar Reflective Elastic Ceramic Membrane.

A Job Well Done

So after four days we had finish painting the roof and the inside temp had gone down at least 4 degrees. The paint was a polyurethane membrane which meant no more water leaking when it rained and would be a lot cooler in summer. We just have to remove the old air conditioner unit which is now under the solar panels. This is way down the back of the coach once done the roof will be totally finished off, in time this back area will also have a deck for us one day.

On the road problems

Why Don’t I Have Power

23/05/2017 Bernie Cross

First Day On The Road

Leaving Leigh Creek S.A on the start of our new life, We had to be in Yulara to start work in five days. With a smile on our faces the next stop was port Augusta for the night, then head north on the Stuart Hwy. The coach was packed full with only room down the front for our bed and some were to cook on the road.

On the road camping in the coach all packed up.

Too Good To Be True

All was going fine, then I started to lose a little bit of power we were only 150 klms down the road and almost to Hawker. Just an other 140 ks to Port Augusta I thought, then the gauges on the dash started flutter around. Thats when the coach started to drop the RPM of every 30 klms…. I was losing around 100-150 RPM, it looked like some electrical gremlin had raised it’s ugly head. We made it into Port Augusta but just at a max speed of 60k/h, fill it up at the first servo we came to. After a 750 Lt hole in my pocket an 1000 Lt tank sounds great till you have to fill it up.

Let’s Sleep On It

After a good nights sleep it was off to the truck work shop across the road. They just so happen to have someone free to start working on it there and then… How good was that? So off we to the shops to stock up on things you can’t get in the middle of nowhere. ( Yulara NT).

Back at the workshop they had found after 3 hrs it was not an electrical problem at all but a fuel supply problem…..in particular the in tank filter. Bugger I’d just filled the bloody thing up and now It has to drain the hole lot, so 5 x 205 Lt drums later it was 5pm on a Friday night and the filter was out.

Back On the Road

So by Monday afternoon, the filter was clean, pumping the diesel back into the tank, we’re back on the road.

Curtain Springs to Alice

But about 9 months later driving into Alice Springs….. Oh bugger it’s happening again! With only 450 Lt in the tank and some drums from a caravan park, we drained the tank again. This time it was modification time because that filter was not going back in again. Some more shopping in Alice and a movie it was back to fix the filter system for good.

New diesel filter on the outside with ballcock valves so I can have it cleaned in 20min.

We are still getting sludge out of the tank I’ve cleaned it out about 5 times now, but the tank is slowly cleaning it’s self out. I just have to remember to turn the valves back on after I clean the filter, yes I did forget the first time and had to bleed the diesel pump to get it going again. You only ever do it once..